# Reconstruction intent and acceptance; all coordinates use the supplied native frame. # Whole-part volume/surface/COM are diagnostic in brief.md, not exterior-style gates. schema_version: 1 name: voron-sb-duct intent: 'Reconstruct the Voron Stealthburner printhead front housing (Rapido V2 variant) as editable, parameterized KCL from the attached renders, section drawings and dimension sheet, in the reference frame (x symmetric about 0, back mating face y = 0 with the part extending to y = -27.4, z from 2.37 at the nozzle end to 61.5 at the top). The interior matters most: two mirrored closed part-cooling ducts from the top fan inlets down to the forked nozzle outlets (about 8 x 19 mm channels with ~1 mm walls, never connected to each other), the hotend cavity (about 26 x 35 mm, open to the back and the nozzle end) with the round hotend-fan opening on the front, and the screw holes. Declare the duct probe points as void probes, the sections as acceptance sections, the ducts as passages and the wall minimum as a thickness check. Cosmetic styling, text and grille are optional. One solid; export STEP and STL. Reference CAD is evaluator-only.' units: length: mm angle: deg material: null density_kg_m3: null process: Printed housing; exact additive process and material unspecified. release_status: reconstruction frame: origin: Intersection of the toolhead center plane x=0 and the back mating plane y=0 with the reference z=0 plane. This lies in the open center, 2.367 mm below the lowest material. Do not move the bbox minimum to the origin. axes: x: Positive to the right in front.png; left/right duct routes straddle x=0. back.png uses horizontal -x. y: Positive out through the back mating face toward the mating toolhead. Housing material extends into negative y, from y=0 to the front at y=-27.4. z: Positive upward away from the nozzle end toward the top inlet rim; lowest material z=2.367 and top z=61.5. datums: - name: A description: Back mating patches on y=0, outward normal +y. - name: B description: Center reference plane x=0, halfway between envelope extrema x=-35.534 and +35.534; local hardware and mouth details are not all symmetric. - name: C description: Top inlet-rim plane z=61.5; reference z=0 is 61.5 mm below this plane, not on the part. envelope: min: - -35.534 - -27.4 - 2.367 max: - 35.534 - 0 - 61.5 tolerance: 0.1 parameters: - name: overallWidth value: 71.068 unit: mm provenance: stated tolerance: 0.1 description: Envelope x extent; width is centered about x=0. source: sources/dimension-sheet.md - name: overallDepth value: 27.4 unit: mm provenance: stated tolerance: 0.1 description: Distance from back datum y=0 to front y=-27.4. source: sources/dimension-sheet.md - name: nozzleEndZ value: 2.367 unit: mm provenance: stated tolerance: 0.1 description: Lowest material; preserve the native z offset. source: sources/dimension-sheet.md - name: topZ value: 61.5 unit: mm provenance: stated tolerance: 0.1 description: Upper inlet rim plane. source: sources/dimension-sheet.md - name: backY value: 0 unit: mm provenance: stated tolerance: 0.05 description: Back mating datum position. source: sources/dimension-sheet.md - name: overallHeight value: 59.133 unit: mm provenance: derived tolerance: 0.1 description: Envelope height, not an instruction to rebase the part. formula: topZ - nozzleEndZ - name: halfWidth value: 35.534 unit: mm provenance: derived tolerance: 0.05 description: Magnitude of both x envelope limits. formula: overallWidth / 2 - name: frontY value: -27.4 unit: mm provenance: derived tolerance: 0.05 description: Front-facing plane. formula: backY - overallDepth - name: ductCount value: 2 unit: '' provenance: stated tolerance: 0.01 description: Two isolated mirrored part-cooling routes. source: sources/voron-duct-description.md - name: outletsPerDuct value: 2 unit: '' provenance: stated tolerance: 0.01 description: Each route forks into two nozzle outlets. source: sources/voron-duct-description.md - name: ductWidth value: 8 unit: mm provenance: stated tolerance: 2 description: Approximate interior x width at the middle duct stations, not the exterior wall width. source: sources/voron-duct-description.md - name: ductDepth value: 19 unit: mm provenance: stated tolerance: 2 description: Approximate interior y span at z=30..45. source: sources/voron-duct-description.md - name: ductWall value: 1 unit: mm provenance: stated tolerance: 0.25 description: Nominal closed duct wall; thickness acceptance remains p05 >= 0.75. source: sources/voron-duct-description.md - name: wallMinimum value: 0.75 unit: mm provenance: stated tolerance: 0.01 description: Required fifth-percentile inward-ray thickness; not a claim that every local minimum is 0.75. source: sources/voron-duct-description.md - name: hotendCavityWidth value: 26 unit: mm provenance: stated tolerance: 2 description: Approximate hotend pocket width, independent of the larger front fan mouth. source: sources/voron-duct-description.md - name: hotendCavityHeight value: 35 unit: mm provenance: stated tolerance: 3 description: Approximate hotend pocket vertical extent. source: sources/voron-duct-description.md - name: hotendCavityBottomZ value: 9 unit: mm provenance: stated tolerance: 2 description: Approximate start of hotend pocket; nozzle access continues downward. source: sources/voron-duct-description.md - name: hotendCavityTopZ value: 44 unit: mm provenance: derived tolerance: 3 description: Approximate hotend pocket top, not the z=54 rear fan-transition roof. formula: hotendCavityBottomZ + hotendCavityHeight - name: fanOpeningDiameter value: 37.5 unit: mm provenance: measured tolerance: 1.5 description: Nominal front round opening width; loft into the rear rounded-rectangle opening instead of forcing a full cylindrical bore. source: sources/front.png - name: fanCenterZ value: 43.3 unit: mm provenance: measured tolerance: 0.8 description: Nominal front fan-opening center height. source: sources/front.png - name: ductMidCenterX value: 22 unit: mm provenance: measured tolerance: 1 description: Positive magnitude of mirrored mid-height duct centerlines. source: sources/section-z45.png - name: ductMidCenterY value: -16.5 unit: mm provenance: measured tolerance: 1 description: Middle duct y center shared by both sides. source: sources/section-z45.png - name: leftInletCenterX value: -17.5 unit: mm provenance: measured tolerance: 1.5 description: Local top mouth estimate; retain mirror routing below the mouth transition, see open question Q2. source: sources/top.png - name: rightInletCenterX value: 11.75 unit: mm provenance: measured tolerance: 1.5 description: Local top mouth estimate; retain mirror routing below the mouth transition, see open question Q2. source: sources/top.png - name: leftInletWidth value: 15 unit: mm provenance: measured tolerance: 1.5 description: Local top mouth estimate; retain mirror routing below the mouth transition, see open question Q2. source: sources/top.png - name: rightInletWidth value: 13.5 unit: mm provenance: measured tolerance: 1.5 description: Local top mouth estimate; retain mirror routing below the mouth transition, see open question Q2. source: sources/top.png - name: inletDepth value: 8.2 unit: mm provenance: measured tolerance: 1 description: Local top mouth estimate; retain mirror routing below the mouth transition, see open question Q2. source: sources/top.png - name: inletCenterY value: -19 unit: mm provenance: measured tolerance: 1 description: Local top mouth estimate; retain mirror routing below the mouth transition, see open question Q2. source: sources/top.png - name: topHoleAx value: -6.963 unit: mm provenance: stated tolerance: 0.15 description: First vertical screw axis x. source: sources/dimension-sheet.md - name: topHoleAy value: -3.939 unit: mm provenance: stated tolerance: 0.15 description: First vertical screw axis y. source: sources/dimension-sheet.md - name: topHoleBx value: 3.939 unit: mm provenance: stated tolerance: 0.15 description: Second vertical screw axis x. source: sources/dimension-sheet.md - name: topHoleBy value: -6.963 unit: mm provenance: stated tolerance: 0.15 description: Second vertical screw axis y. source: sources/dimension-sheet.md - name: topPilotDiameter value: 2.7 unit: mm provenance: stated tolerance: 0.1 description: Both vertical pilot bores. source: sources/dimension-sheet.md edit_test: delta: 0.2 expect: volume_delta: -7.037167544041143 direction: decrease tolerance_rel: 0.08 bbox_delta: - 0 - 0 - 0 infeasible_deltas: - 3.0 - name: topCounterboreDiameter value: 5 unit: mm provenance: stated tolerance: 0.1 description: Both vertical counterbores. source: sources/dimension-sheet.md - name: topPilotStartZ value: 54 unit: mm provenance: stated tolerance: 0.15 description: Bottom of vertical pilot bores. source: sources/dimension-sheet.md - name: topBoreCylinderEndZ value: 60.9 unit: mm provenance: stated tolerance: 0.15 description: Top of straight cylindrical counterbore; entry treatment reaches topZ. source: sources/dimension-sheet.md - name: topCounterboreDepth value: 2.9 unit: mm provenance: stated tolerance: 0.15 description: Length of straight counterbore; edit moves its floor while retaining the top entry. source: sources/dimension-sheet.md edit_test: delta: 0.4 expect: volume_delta: -11.127521179015048 direction: decrease tolerance_rel: 0.08 bbox_delta: - 0 - 0 - 0 sweep: values: - 2.5 - 2.9 - 3.3 infeasible_deltas: - 5.0 - name: upperMountHalfSpacing value: 12.7 unit: mm provenance: stated tolerance: 0.15 description: Rear upper screw axes at x=+/-12.7. source: sources/dimension-sheet.md - name: upperMountZ value: 55.424 unit: mm provenance: stated tolerance: 0.15 description: Rear upper screw center height. source: sources/dimension-sheet.md - name: upperMountDiameter value: 4.6 unit: mm provenance: stated tolerance: 0.1 description: Rear upper bore diameters. source: sources/dimension-sheet.md - name: upperMountLeftStartY value: -6 unit: mm provenance: stated tolerance: 0.15 description: Left rear upper bore start. source: sources/dimension-sheet.md - name: upperMountRightStartY value: -5.861 unit: mm provenance: stated tolerance: 0.15 description: Right rear upper bore start. source: sources/dimension-sheet.md - name: rearBoreEndY value: -0.4 unit: mm provenance: stated tolerance: 0.15 description: End of the straight upper/auxiliary rear bores before their entry chamfers. source: sources/dimension-sheet.md - name: auxLowerX value: -28 unit: mm provenance: stated tolerance: 0.15 description: Lower auxiliary rear screw axis x. source: sources/dimension-sheet.md - name: auxLowerZ value: 19 unit: mm provenance: stated tolerance: 0.15 description: Lower auxiliary rear screw axis z. source: sources/dimension-sheet.md - name: auxUpperX value: -25 unit: mm provenance: stated tolerance: 0.15 description: Upper auxiliary rear screw axis x. source: sources/dimension-sheet.md - name: auxUpperZ value: 35 unit: mm provenance: stated tolerance: 0.15 description: Upper auxiliary rear screw axis z. source: sources/dimension-sheet.md - name: auxBoreDiameter value: 4.7 unit: mm provenance: stated tolerance: 0.1 description: Both left auxiliary rear bores. source: sources/dimension-sheet.md - name: auxLowerStartY value: -4.2 unit: mm provenance: stated tolerance: 0.15 description: Lower auxiliary bore start. source: sources/dimension-sheet.md - name: auxUpperStartY value: -4.257 unit: mm provenance: stated tolerance: 0.15 description: Upper auxiliary bore start. source: sources/dimension-sheet.md - name: lowerMountHalfSpacing value: 16.25 unit: mm provenance: stated tolerance: 0.15 description: Lower mounting screw axes x=+/-16.25. source: sources/dimension-sheet.md - name: lowerMountZ value: 19.301 unit: mm provenance: stated tolerance: 0.15 description: Lower mounting screw axis height. source: sources/dimension-sheet.md - name: lowerMountDiameter value: 3.4 unit: mm provenance: stated tolerance: 0.1 description: Lower mounting bore diameter over the documented rear segment. source: sources/dimension-sheet.md - name: lowerMountBoreLength value: 7.5 unit: mm provenance: stated tolerance: 0.2 description: Documented straight segment y=-7.5..0; forward continuation is visible but not dimensioned as the same bore. source: sources/dimension-sheet.md - name: rearCableNotchDiameter value: 4.1 unit: mm provenance: stated tolerance: 0.15 description: Partial vertical cylindrical notch on the back edge, not a closed through-hole. source: sources/dimension-sheet.md - name: topCounterboreFloorZ value: 58 unit: mm provenance: derived tolerance: 0.15 description: Counterbore/pilot shoulder height. formula: topBoreCylinderEndZ - topCounterboreDepth - name: topPilotLength value: 4 unit: mm provenance: derived tolerance: 0.2 description: Pilot length remaining beneath the counterbore floor. formula: topCounterboreFloorZ - topPilotStartZ features: - id: housingEnvelope kind: profile description: One connected housing in the native reference frame, with two separated lower legs and the source silhouette. Envelope-only blockout is a full bounding prism before functional cuts. parameters: - overallWidth - overallDepth - nozzleEndZ - topZ - backY - overallHeight - halfWidth - frontY verify: - method: bbox - method: solid points: - - 0 - -10 - 58.8 - method: dimension dimension: envelopeWidth - method: dimension dimension: envelopeDepth - method: dimension dimension: envelopeHeight - method: dimension dimension: frontToBack optional: false - id: leftCoolingDuct kind: channel description: Closed curved part-cooling route, top inlet, descending side trunk, and two inward/downward nozzle branches. Mirror the principal duct route about x=0; retain documented asymmetric local inlet/rail transitions. Must satisfy passage connectivity and cross-duct isolation. parameters: - ductCount - outletsPerDuct - ductWidth - ductDepth - ductWall - wallMinimum - ductMidCenterX - ductMidCenterY - leftInletCenterX - rightInletCenterX - leftInletWidth - rightInletWidth - inletDepth - inletCenterY verify: - method: void points: - - -20 - -18 - 55 - - -22 - -16 - 45 - - -24 - -14 - 30 - - -27 - -12 - 20 - - -22 - -8 - 7.5 - - -22 - -22 - 8 - method: section section: sec_z10 - method: section section: sec_z20 - method: section section: sec_z30 - method: section section: sec_z45 - method: section section: sec_z55 - method: face face: topInletRim - method: face face: nozzleBaseLeft - method: plane plane: leftOutletInnerLip - method: plane plane: leftOutletReturn - method: void points: - - -15 - -19 - 60 - - -15 - -19 - 61 - - -15 - -19 - 62 note: Open actual top inlet; z=62 is deliberately above the part. optional: false count: 1 - id: rightCoolingDuct kind: channel description: Closed curved part-cooling route, top inlet, descending side trunk, and two inward/downward nozzle branches. Mirror the principal duct route about x=0; retain documented asymmetric local inlet/rail transitions. Must satisfy passage connectivity and cross-duct isolation. parameters: - ductCount - outletsPerDuct - ductWidth - ductDepth - ductWall - wallMinimum - ductMidCenterX - ductMidCenterY - leftInletCenterX - rightInletCenterX - leftInletWidth - rightInletWidth - inletDepth - inletCenterY verify: - method: void points: - - 20 - -18 - 55 - - 22 - -16 - 45 - - 24 - -14 - 30 - - 27 - -12 - 20 - - 22 - -8 - 7.5 - - 22 - -22 - 8 - method: section section: sec_z10 - method: section section: sec_z20 - method: section section: sec_z30 - method: section section: sec_z45 - method: section section: sec_z55 - method: face face: topInletRim - method: face face: nozzleBaseRight - method: plane plane: rightOutletInnerLip - method: plane plane: rightOutletReturn - method: void points: - - 10 - -19 - 60 - - 10 - -19 - 61 - - 10 - -19 - 62 note: Open actual top inlet; z=62 is deliberately above the part. optional: false count: 1 - id: nozzleForks kind: channel description: Two outlets per duct, four total. Ducts remain independent; neither opens into the hotend cavity. parameters: - outletsPerDuct - ductWidth - ductDepth - ductWall verify: - method: section section: sec_z10 - method: section section: sec_x-22 - method: section section: sec_x22 optional: false count: 4 - id: hotendPocket kind: cavity description: Rounded pocket, approximately 26 x 35 mm, open to the rear and nozzle end; rear fan-transition roof at z=54 is a separate boundary. parameters: - hotendCavityWidth - hotendCavityHeight - hotendCavityBottomZ - hotendCavityTopZ verify: - method: void points: - - 0 - -5 - 36 - - 0 - -5 - 20 - - 0 - -12 - 10 - - 0 - -20 - 10 - method: dimension dimension: hotendWallSpacing - method: face face: hotendRearRoof - method: section section: sec_y-12 - method: section section: sec_x0 - method: plane plane: hotendLowerRamp - method: plane plane: hotendBridgeRamp - method: plane plane: hotendFrontUnderside optional: false - id: hotendFanOpening kind: loft description: Round front mouth lofts to a smaller rear rounded rectangle and intersects the hotend access cavity. The nominal front diameter does not describe a constant cylindrical bore. parameters: - fanOpeningDiameter - fanCenterZ verify: - method: void points: - - 12 - -27 - 45 - - 12 - -24 - 45 - - -12 - -27 - 42 - - -12 - -24 - 42 - method: face face: frontFanRim - method: section section: sec_y-20 - method: section section: sec_y-12 optional: false - id: topSteppedFasteners kind: hole description: Two vertical stepped screw holes; preserve pilot axes and top entry positions through the two declared independent edits. parameters: - topHoleAx - topHoleAy - topHoleBx - topHoleBy - topPilotDiameter - topCounterboreDiameter - topPilotStartZ - topBoreCylinderEndZ - topCounterboreDepth - topCounterboreFloorZ - topPilotLength verify: - method: cylinder cylinder: topCounterboreA - method: cylinder cylinder: topCounterboreB - method: cylinder cylinder: topPilotA - method: cylinder cylinder: topPilotB - method: face face: topCounterboreFloorA - method: face face: topCounterboreFloorB - method: face face: topInletRim - method: face face: hotendRearRoof - method: section section: sec_z55 optional: false count: 2 - id: upperRearFasteners kind: hole description: Two upper rear screws and their located boss surfaces. parameters: - upperMountHalfSpacing - upperMountZ - upperMountDiameter - upperMountLeftStartY - upperMountRightStartY - rearBoreEndY verify: - method: cylinder cylinder: rearUpperLeftBore - method: cylinder cylinder: rearUpperRightBore - method: cylinder cylinder: upperLeftMountBoss - method: face face: upperLeftBoreSeat - method: face face: upperRightBoreSeat optional: false count: 2 - id: leftAuxFasteners kind: hole description: Two auxiliary rear screw holes on the negative-x side; do not mirror onto the other side. parameters: - auxLowerX - auxLowerZ - auxUpperX - auxUpperZ - auxBoreDiameter - auxLowerStartY - auxUpperStartY - rearBoreEndY verify: - method: cylinder cylinder: rearAuxLowerBore - method: cylinder cylinder: rearAuxUpperBore - method: face face: auxLowerSeat - method: face face: auxUpperSeat optional: false count: 2 - id: lowerMounts kind: boss description: Two lower mounting holes and unequal source boss blends. Rear cylindrical length is stated; front access continuation is visible and must remain open. parameters: - lowerMountHalfSpacing - lowerMountZ - lowerMountDiameter - lowerMountBoreLength verify: - method: cylinder cylinder: lowerLeftMountBore - method: cylinder cylinder: lowerRightMountBore - method: cylinder cylinder: lowerLeftMountBoss - method: cylinder cylinder: lowerRightMountBoss - method: cylinder cylinder: lowerRightBossBlendA - method: cylinder cylinder: lowerRightBossBlendB - method: section section: sec_y-12 - method: section section: sec_y-20 - method: void points: - - -16.25 - -26 - 19.301 - - 16.25 - -26 - 19.301 - - -16.25 - -20 - 19.301 - - 16.25 - -20 - 19.301 - - -16.25 - -12 - 19.301 - - 16.25 - -12 - 19.301 note: Located void centers of the two front-visible lower screw access paths, corroborated by front.png and sections y=-20 and y=-12. No additional bore diameter or chamfer depth is inferred for this continuation. optional: false count: 2 - id: rearCableRelief kind: cut description: Partial vertical back-edge cable notch, centered at x=0, y=0, spanning the stated cylinder z=54..60.9. parameters: - rearCableNotchDiameter verify: - method: cylinder cylinder: rearCableNotch optional: false - id: locatedCurvedTransitions kind: loft description: All remaining located partial concave/convex cylindrical patches from the dimension sheet. These are trimmed transitions, not additional disconnected pins or complete drilled holes. Their angular limits must follow section silhouettes. parameters: [] verify: - method: cylinder cylinder: cavityLowerRelief - method: cylinder cylinder: cavityUpperRelief - method: cylinder cylinder: leftInletTurn - method: cylinder cylinder: rightRearRelief - method: cylinder cylinder: leftHotendDiagonalRelief - method: cylinder cylinder: rightHotendDiagonalRelief - method: cylinder cylinder: rightObliqueReliefA - method: cylinder cylinder: rightObliqueReliefB - method: cylinder cylinder: leftRailConcaveBlend - method: cylinder cylinder: rightDuctConvexTurn - method: cylinder cylinder: rightCavityConvexBlend - method: cylinder cylinder: rightInletConvexTurn - method: cylinder cylinder: leftRailLowerBlend - method: cylinder cylinder: leftRailUpperBlend optional: false - id: rearMatingPatches kind: profile description: Preserve five individually named coplanar mating patches and offset rail seats. parameters: - backY verify: - method: face face: backLeftMain - method: face face: backRightMain - method: face face: backRightMount - method: face face: backLeftOutletLip - method: face face: backRightOutletLip - method: face face: leftMountRail - method: face face: leftRearRailSeat - method: face face: rightRearSeat optional: false - id: nozzleUndersides kind: profile description: Located inclined material surfaces and low support lands around the four angled air outlets. parameters: - nozzleEndZ verify: - method: plane plane: leftNozzleBottom - method: plane plane: rightNozzleBottom - method: face face: nozzleBaseLeft - method: face face: nozzleBaseRight optional: false - id: cosmeticOuterFacets kind: chamfer description: Optional exterior facets, small chamfers and fillets visible in front/back/left/right/isometric views. Functional walls, located cylindrical transitions, envelope, and port lips remain mandatory. parameters: [] verify: - method: bbox note: No cosmetic face count or exact exterior deviation is imposed. optional: true - id: cosmeticTextAndArrows kind: cut description: Optional top P-RPDV2 marking and two curved front arrows/recesses. Text font, relief depth and stroke width are not specified. parameters: [] verify: - method: bbox note: Marking appearance has no hard acceptance value. optional: true - id: cosmeticFanGrille kind: rib description: 'Central hub REQUIRED, vanes optional. The fan opening carries a solid central hub, about 16 mm wide (x -8..8) and 15 mm tall (z ~36..51, centred a little above the bore axis), running the full depth of the opening from the front face to the bore floor at y = -19.2; it is drawn in the y=-20 section and the front/isometric views. The scored sections z=45 (566 mm2, 8 % band: the hub is ~130 mm2 of it) and y=-20 pass through the hub, so a part without it cannot meet them; the description calls the grille cosmetic, this contract does not. The four swept vanes joining the hub to the rim are optional; with or without them the round front opening and both part-cooling ducts stay as drawn.' parameters: [] verify: - method: section section: sec_z45 note: The hub is a third material island at z=45 between the two side regions; the area band includes it. - method: solid points: - [0, -23, 41] - [0, -23, 45] - [4, -23, 43] - [-4, -23, 43] note: Hub material at mid-depth of the opening (see probe fanHubSolid). optional: false count: 4 interfaces: - name: nativeDatums description: Back plane and native envelope positions survive later internal edits. must_not_change: true checks: - envelopeWidth - envelopeDepth - envelopeHeight - frontToBack - backLeftMain - backRightMain - backRightMount - backLeftOutletLip - backRightOutletLip - frontFanRim - name: coolingInletsAndOutlets description: Common top rim, separate lower lips, and functional duct sections remain in place. Connectivity/isolation additionally run as global acceptance passages. must_not_change: true checks: - topInletRim - nozzleBaseLeft - nozzleBaseRight - leftOutletInnerLip - rightOutletInnerLip - leftOutletReturn - rightOutletReturn - sec_z10 - sec_z20 - sec_z30 - sec_z45 - sec_z55 - name: hotendAccess description: Retain rear/nozzle access and cavity support faces. must_not_change: true checks: - hotendLeftWall - hotendRightWall - hotendWallSpacing - hotendRearRoof - hotendBridgeBottom - hotendBridgeTopLeft - hotendBridgeTopRight - sec_y-12 - sec_x0 - name: topScrewInterface description: Top pilot/counterbore axes and seats; only the two declared driven dimensions vary during their edits. must_not_change: true checks: - topPilotA - topPilotB - topCounterboreA - topCounterboreB - topCounterboreFloorA - topCounterboreFloorB - name: rearScrewInterfaces description: Upper, lower and auxiliary rear screw axes and material bosses stay fixed. must_not_change: true checks: - rearUpperLeftBore - rearUpperRightBore - rearAuxLowerBore - rearAuxUpperBore - lowerLeftMountBore - lowerRightMountBore - upperLeftMountBoss - lowerLeftMountBoss - lowerRightMountBoss - name: rearCableInterface description: Preserve the partial open back-edge cable notch. must_not_change: true checks: - rearCableNotch acceptance: bbox_tolerance: 0.1 volume: null surface_area: null center_of_mass: null solid_count: 1 sections: - id: sec_x-22 plane: x at: -22 expect: area: 869.5 area_tolerance_rel: 0.18 loops: 1 holes: 2 description: Left longitudinal wall and two fork-branch holes; main duct opens upward at this x station. Image label 870.48 mm2. Table and drawing differ by 0.11%. - id: sec_x0 plane: x at: 0 expect: area: 369.1 area_tolerance_rel: 0.55 holes: 0 islands_min: 2 description: Roof and lower bridge are mandatory; the third reference region is the optional grille hub. Image label 368.74 mm2. The 55% area band allows removal of the hub, not removal of the roof or bridge. - id: sec_x22 plane: x at: 22 expect: area: 733.52 area_tolerance_rel: 0.18 loops: 1 holes: 3 description: 'Right longitudinal section: a closed upper duct section plus two fork-branch holes. Image label 734.37 mm2. Local inlet transitions are asymmetric in the source.' - id: sec_y-5 plane: y at: -5 expect: area: 1726.99 area_tolerance_rel: 0.12 islands_min: 2 description: 'Use the dimension-sheet area. Its loops=3 and holes=6 are recorded as diagnostic counts only: the image caption instead reports 55.37 mm2 and 5 regions with visibly open contours. Resolve Q1 before enforcing exact topology here.' - id: sec_y-12 plane: y at: -12 expect: area: 1412.07 area_tolerance_rel: 0.06 loops: 1 holes: 5 description: One connected material region, two duct holes, central fan-transition hole, and two lower mounting holes. Image label 1414.64 mm2. - id: sec_y-20 plane: y at: -20 expect: area: 1459.74 area_tolerance_rel: 0.08 islands_min: 1 description: 'Image area 1461.32 mm2: one connected body (ducts, chin, shoulders and the required central hub, which is about 230 mm2 of this station) plus two isolated cosmetic rib islands of ~4 mm2 near the top that are not imposed (loops=3, holes=6 in the image). The hub is not optional here: without it the station reads ~230 mm2 low, and a part that reaches the band without it carries that much material somewhere the drawing shows air. Hole count is not imposed (vanes and ribs vary it).' - id: sec_z10 plane: z at: 10 expect: area: 435.42 area_tolerance_rel: 0.08 holes: 4 islands_min: 2 description: Two functional side bodies containing four separate branch holes. Reference loops=3 includes a tiny 0.82 x 0.25 mm region; do not require that cosmetic island. Image label 436.53 mm2. - id: sec_z20 plane: z at: 20 expect: area: 765.96 area_tolerance_rel: 0.25 loops: 3 holes: 2 description: Three material regions and two duct holes before the lower fork. Image label 618.29 mm2 conflicts with the table by 19.28%; the 25% band covers that disclosed source discrepancy, Q1. - id: sec_z30 plane: z at: 30 expect: area: 739.16 area_tolerance_rel: 0.08 loops: 2 holes: 2 description: Two side material regions and two enclosed duct holes. Image label 739.93 mm2. Thin cosmetic vane stubs do not change the two duct holes. - id: sec_z45 plane: z at: 45 expect: area: 565.96 area_tolerance_rel: 0.08 holes: 2 islands_min: 2 description: Exactly two enclosed duct holes. Reference loops=3 includes the optional central grille hub; at least the two side material regions must remain. Image label 566.26 mm2. - id: sec_z55 plane: z at: 55 expect: area: 821.64 area_tolerance_rel: 0.15 loops: 1 holes: 4 description: Upper connected shell with two duct voids and two vertical pilot bores. Image label 821.63 mm2. faces: - name: backLeftMain plane: y at: 0 normal: + center: - -16.22 - 40.42 mode: one area: 422.38 area_tolerance_rel: 0.35 tolerance: 1.5 - name: backRightMain plane: y at: 0 normal: + center: - 11.67 - 49.48 mode: one area: 214.31 area_tolerance_rel: 0.35 tolerance: 1.5 - name: backRightMount plane: y at: 0 normal: + center: - 16.47 - 19.74 mode: one area: 27.8 area_tolerance_rel: 0.35 tolerance: 1.5 - name: backLeftOutletLip plane: y at: 0 normal: + center: - -18.22 - 3.97 mode: one area: 12.67 area_tolerance_rel: 0.35 tolerance: 1.5 - name: backRightOutletLip plane: y at: 0 normal: + center: - 18.22 - 3.97 mode: one area: 12.67 area_tolerance_rel: 0.35 tolerance: 1.5 - name: frontFanRim plane: y at: -27.4 normal: '-' mode: one area: 1661.02 area_tolerance_rel: 0.35 tolerance: 0.1 - name: topInletRim plane: z at: 61.5 normal: + center: - -0.39 - -14.07 mode: one area: 955.18 area_tolerance_rel: 0.35 tolerance: 1.5 - name: nozzleBaseLeft plane: z at: 2.367 normal: '-' center: - -17.14 - -10.47 mode: one area: 34.67 area_tolerance_rel: 0.3 tolerance: 1 - name: nozzleBaseRight plane: z at: 2.367 normal: '-' center: - 17.14 - -10.47 mode: one area: 34.67 area_tolerance_rel: 0.3 tolerance: 1 - name: hotendLeftWall plane: x at: -13.15 normal: + center: - -3.72 - 21.65 mode: one area: 59.84 area_tolerance_rel: 0.3 tolerance: 1 - name: hotendRightWall plane: x at: 13.15 normal: '-' center: - -5.66 - 20.23 mode: one area: 29.82 area_tolerance_rel: 0.3 tolerance: 1 - name: leftMountRail plane: x at: -14.465 normal: '-' center: - -2.33 - 37.13 mode: one area: 113.73 area_tolerance_rel: 0.3 tolerance: 1 - name: leftRearRailSeat plane: y at: -4.665 normal: + center: - -17.18 - 37.21 mode: one area: 144.43 area_tolerance_rel: 0.3 tolerance: 1 - name: rightRearSeat plane: y at: -3.8 normal: + center: - 21.82 - 25.9 mode: one area: 301.52 area_tolerance_rel: 0.3 tolerance: 1 - name: upperLeftBoreSeat plane: y at: -6 normal: + center: - -12.7 - 55.42 mode: one area: 16.62 area_tolerance_rel: 0.3 tolerance: 0.5 - name: upperRightBoreSeat plane: y at: -5.861 normal: + center: - 12.7 - 55.42 mode: one area: 16.62 area_tolerance_rel: 0.3 tolerance: 0.5 - name: auxLowerSeat plane: y at: -4.2 normal: + center: - -28 - 19 mode: one area: 9.31 area_tolerance_rel: 0.35 tolerance: 0.5 - name: auxUpperSeat plane: y at: -4.2 normal: + center: - -24.98 - 35 mode: one area: 9.24 area_tolerance_rel: 0.35 tolerance: 0.5 - name: hotendRearRoof plane: z at: 54 normal: '-' center: - 0.12 - -4.23 mode: one area: 141.02 area_tolerance_rel: 0.3 tolerance: 1 - name: hotendBridgeBottom plane: z at: 27.8 normal: '-' center: - -1.11 - -8.52 mode: one area: 85.83 area_tolerance_rel: 0.3 tolerance: 1 - name: hotendBridgeTopRight plane: z at: 29 normal: + center: - 3 - -10.41 mode: one area: 24.55 area_tolerance_rel: 0.3 tolerance: 1 - name: hotendBridgeTopLeft plane: z at: 29 normal: + center: - -8.06 - -8.52 mode: one area: 10.01 area_tolerance_rel: 0.3 tolerance: 1 - name: lowerMountUndersideLeft plane: z at: 16.001 normal: '-' center: - -16.75 - -9.75 mode: one area: 54.8 area_tolerance_rel: 0.3 tolerance: 1 - name: lowerMountUndersideRight plane: z at: 16.001 normal: '-' center: - 16.66 - -12.01 mode: one area: 40.96 area_tolerance_rel: 0.3 tolerance: 1 - name: topCounterboreFloorA plane: z at: 58 normal: + center: - -6.96 - -3.94 mode: one area: 13.91 area_tolerance_rel: 0.3 tolerance: 0.6 - name: topCounterboreFloorB plane: z at: 58 normal: + center: - 3.94 - -6.96 mode: one area: 13.91 area_tolerance_rel: 0.3 tolerance: 0.6 cylinders: - name: cavityLowerRelief point: - 0.0 - -0.0 - 28.581 direction: - -0.0 - -0.0 - 1.0 kind: hole diameter: 22.5 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 1.562 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 1. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 27.8 .. 29.362 (from axis point [0.0, -0.0, 0.0]).' - name: cavityUpperRelief point: - -0.0 - 0.0 - 52.308 direction: - -0.0 - 0.0 - 1.0 kind: hole diameter: 20.4 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 3.384 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 2. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 50.616 .. 54 (from axis point [0.0, -0.0, 0.0]).' - name: leftInletTurn point: - -18.034 - -21.953 - 54.064 direction: - 1.0 - 0.0 - -0.0 kind: hole diameter: 20.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 13.403 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 3. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -24.736 .. -11.333 (from axis point [0.0, -21.953, 54.064]).' - name: rightRearRelief point: - 18.491 - -3.205 - 17.626 direction: - 0.0 - 1.0 - -0.0 kind: hole diameter: 20.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 1.191 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 4. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -3.8 .. -2.609 (from axis point [18.491, 0.0, 17.626]).' - name: leftHotendDiagonalRelief point: - -5.15 - -7.564 - 21.521 direction: - 0.0 - 0.7071 - 0.7071 kind: hole diameter: 16.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 17.759 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 5. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 0.989 .. 18.748 (from axis point [-5.15, -14.542, 14.544]).' - name: rightHotendDiagonalRelief point: - 5.15 - -8.193 - 20.893 direction: - 0.0 - 0.7071 - 0.7071 kind: hole diameter: 16.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 15.981 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 6. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 0.989 .. 16.969 (from axis point [5.15, -14.542, 14.544]).' - name: topCounterboreA point: - -6.963 - -3.939 - 0 direction: - -0.0 - 0.0 - 1.0 kind: hole diameter: 5.0 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 2.9 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 7. Full circular bore segment. Source axis extent: 58 .. 60.9 (from axis point [-6.963, -3.939, -0.0]).' t_range: - 58 - 60.9 - name: topCounterboreB point: - 3.939 - -6.963 - 0 direction: - -0.0 - 0.0 - 1.0 kind: hole diameter: 5.0 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 2.9 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 8. Full circular bore segment. Source axis extent: 58 .. 60.9 (from axis point [3.939, -6.963, 0.0]).' t_range: - 58 - 60.9 - name: rearAuxLowerBore point: - -28.0 - -2.3 - 19.0 direction: - 0.0 - 1.0 - -0.0 kind: hole diameter: 4.7 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 3.8 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 9. Full circular bore segment. Source axis extent: -4.2 .. -0.4 (from axis point [-28.0, 0.0, 19.0]).' - name: rearAuxUpperBore point: - -25.0 - -2.329 - 35.0 direction: - 0.0 - 1.0 - -0.0 kind: hole diameter: 4.7 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 3.857 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 10. Full circular bore segment. Source axis extent: -4.257 .. -0.4 (from axis point [-25.0, 0.0, 35.0]).' - name: rearUpperLeftBore point: - -12.7 - -3.2 - 55.424 direction: - -0.0 - 1.0 - -0.0 kind: hole diameter: 4.6 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 5.6 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 11. Full circular bore segment. Source axis extent: -6 .. -0.4 (from axis point [-12.7, 0.0, 55.424]).' - name: rearUpperRightBore point: - 12.7 - -3.131 - 55.424 direction: - -0.0 - 1.0 - -0.0 kind: hole diameter: 4.6 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 5.461 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 12. Full circular bore segment. Source axis extent: -5.861 .. -0.4 (from axis point [12.7, 0.0, 55.424]).' - name: rearCableNotch point: - 0.0 - 0.0 - 57.45 direction: - 0.0 - 0.0 - 1.0 kind: hole diameter: 4.1 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 6.9 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 13. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 54 .. 60.9 (from axis point [0.0, -0.0, 0.0]).' - name: rightObliqueReliefA point: - 20.102 - -3.583 - 15.573 direction: - 0.564 - 0.6326 - 0.5308 kind: hole diameter: 4.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 4.212 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 14. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 15.231 .. 19.443 (from axis point [10.323, -14.55, 6.37]).' - name: rightObliqueReliefB point: - 21.417 - -3.196 - 14.219 direction: - 0.791 - 0.607 - 0.0766 kind: hole diameter: 4.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 3.247 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 15. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 14.467 .. 17.714 (from axis point [8.688, -12.962, 12.986]).' - name: leftRailConcaveBlend point: - -18.349 - -2.332 - 33.855 direction: - 0.0 - 1.0 - -0.0 kind: hole diameter: 3.984 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 4.665 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 16. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -4.665 .. -0 (from axis point [-18.349, 0.0, 33.855]).' - name: lowerLeftMountBore point: - -16.25 - -3.75 - 19.301 direction: - 0.0 - 1.0 - -0.0 kind: hole diameter: 3.4 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 7.5 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 17. Full circular bore segment. Source axis extent: -7.5 .. 0 (from axis point [-16.25, 0.0, 19.301]).' - name: lowerRightMountBore point: - 16.25 - -3.75 - 19.301 direction: - 0.0 - 1.0 - -0.0 kind: hole diameter: 3.4 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 7.5 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 18. Full circular bore segment. Source axis extent: -7.5 .. 0 (from axis point [16.25, 0.0, 19.301]).' - name: topPilotA point: - -6.963 - -3.939 - 0 direction: - -0.0 - 0.0 - 1.0 kind: hole diameter: 2.7 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 4.0 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 19. Full circular bore segment. Source axis extent: 54 .. 58 (from axis point [-6.963, -3.939, -0.0]).' t_range: - 54 - 58 - name: topPilotB point: - 3.939 - -6.963 - 0 direction: - -0.0 - 0.0 - 1.0 kind: hole diameter: 2.7 radius_tolerance: 0.1 axis_tolerance: 0.2 length: 4.0 length_tolerance: 0.6 description: 'sources/dimension-sheet.md, cylindrical row 20. Full circular bore segment. Source axis extent: 54 .. 58 (from axis point [3.939, -6.963, 0.0]).' t_range: - 54 - 58 - name: rightDuctConvexTurn point: - 22.774 - -33.8 - 36.775 direction: - 1.0 - -0.0 - -0.0 kind: pin diameter: 60.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 10.704 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 21. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 17.422 .. 28.126 (from axis point [-0.0, -33.8, 36.775]).' - name: rightCavityConvexBlend point: - 10.658 - -1.9 - 40.871 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 16.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 3.8 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 22. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -3.8 .. 0 (from axis point [10.658, 0.0, 40.871]).' - name: upperLeftMountBoss point: - -12.7 - -2.332 - 55.424 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 11.4 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 4.665 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 23. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -4.665 .. 0 (from axis point [-12.7, 0.0, 55.424]).' - name: rightInletConvexTurn point: - 15.093 - -8.519 - 59.745 direction: - 1.0 - -0.0 - 0.0 kind: pin diameter: 10.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 9.057 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 24. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: 10.564 .. 19.621 (from axis point [-0.0, -8.519, 59.745]).' - name: lowerLeftMountBoss point: - -16.25 - -2.332 - 19.301 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 9.4 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 4.665 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 25. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -4.665 .. -0 (from axis point [-16.25, 0.0, 19.301]).' - name: lowerRightBossBlendA point: - 15.902 - -3.092 - 20.001 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 8.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 6.184 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 26. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -6.184 .. 0 (from axis point [15.902, 0.0, 20.001]).' - name: lowerRightBossBlendB point: - 17.15 - -1.9 - 19.068 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 8.0 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 3.8 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 27. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -3.8 .. 0 (from axis point [17.15, 0.0, 19.068]).' - name: lowerRightMountBoss point: - 16.25 - -1.9 - 19.301 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 6.437 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 3.8 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 28. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -3.8 .. 0 (from axis point [16.25, 0.0, 19.301]).' - name: leftRailLowerBlend point: - -21.775 - -2.332 - 27.388 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 3.984 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 4.665 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 29. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -4.665 .. -0 (from axis point [-21.775, 0.0, 27.388]).' - name: leftRailUpperBlend point: - -20.147 - -2.332 - 41.463 direction: - 0.0 - 1.0 - -0.0 kind: pin diameter: 3.984 radius_tolerance: 0.3 axis_tolerance: 0.5 length: 4.665 length_tolerance: 1.0 description: 'sources/dimension-sheet.md, cylindrical row 30. Partial cylindrical surface only: do not replace it by a full bore or an added full pin. Angular extent is not specified. Source axis extent: -4.665 .. -0 (from axis point [-20.147, 0.0, 41.463]).' planes: - name: leftNozzleBottom point: - -27.948 - -27.5 - 4.853 normal: - -0.2416 - 0 - -0.9704 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: rightNozzleBottom point: - 27.948 - -27.5 - 4.853 normal: - 0.2416 - 0 - -0.9704 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: leftOutletInnerLip point: - -15.756 - 0 - 4.61 normal: - 0.971 - 0 - -0.2391 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: rightOutletInnerLip point: - 15.756 - 0 - 4.61 normal: - -0.971 - 0 - -0.2391 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: leftOutletReturn point: - -14.635 - -27.433 - 9.123 normal: - 0.7527 - 0.0698 - 0.6547 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: rightOutletReturn point: - 14.635 - -27.433 - 9.123 normal: - -0.7527 - 0.0698 - 0.6547 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: hotendLowerRamp point: - 0 - -20.256 - 20.625 normal: - 0 - 0.342 - -0.9397 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: hotendBridgeRamp point: - 0 - -19.557 - 20.843 normal: - 0 - 0.7071 - -0.7071 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. - name: hotendFrontUnderside point: - 0 - -15.748 - 17.818 normal: - 0 - -0.1762 - -0.9844 tolerance: 0.75 angle_tolerance_deg: 3 description: sources/dimension-sheet.md, Inclined planar faces. Functional nozzle/clearance surface; given point lies on the infinite supporting plane and may be outside the trimmed face. No area constraint on optional exterior styling. dimensions: - name: envelopeWidth axis: x expected: 71.068 tolerance: 0.1 description: overallWidth; stated bbox size from dimension-sheet.md. - name: envelopeDepth axis: y expected: 27.4 tolerance: 0.1 description: overallDepth; stated bbox size. - name: envelopeHeight axis: z expected: 59.133 tolerance: 0.1 description: topZ - nozzleEndZ. - name: frontToBack axis: y expected: 27.4 tolerance: 0.1 between: - frontFanRim - backLeftMain description: backY - frontY; pin depth using actual material datum faces. - name: hotendWallSpacing axis: x expected: 26.3 tolerance: 0.5 between: - hotendLeftWall - hotendRightWall description: 13.15 - (-13.15), from the two listed cavity walls; supports the about-26 mm pocket width. solids: - name: housing contains_point: - 0 - -10 - 58.8 description: Only connected material body; all walls, lips and bosses must belong to it. Optional grille must join it if retained. hardware: [] clearances: [] passages: - name: leftDuctMid45 point_a: [-20, -18, 55] point_b: [-22, -16, 45] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3474.3 volume_max: 5211.4 description: 'Sealed part-cooling duct: air from the inlet chamber under the top mouth (section z=55) must reach this station through the duct alone. Ports: no plugs. Every opening is shut by the 3.2 mm closing radius alone, exactly as the scorer measures it: the outlet lips are narrower than 6.4 mm, and each inlet channel narrows to a neck under 6.4 mm between the z=55 station and the top mouth (in the drawings the sealed duct ends at z~56; the mouth above the neck is open air), so the sealed volume is the duct from that neck to the outlets. A channel that stays 8 mm wide up to the top face leaks to the exterior and fails. The drawn channel is ~8 x 19 mm with ~1 mm walls below the neck, so the duct itself stays open. Air volume band: reference-class duct ~4300 mm3, +-20 %. Station: section z=45 channel centre.' - name: leftDuctTrunk30 point_a: [-20, -18, 55] point_b: [-24, -14, 30] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3474.3 volume_max: 5211.4 description: 'As leftDuctMid45; station: section z=30 channel centre.' - name: leftDuctLower20 point_a: [-20, -18, 55] point_b: [-27, -12, 20] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3474.3 volume_max: 5211.4 description: 'As leftDuctMid45; station: section z=20 channel centre.' - name: leftDuctRearOutlet point_a: [-20, -18, 55] point_b: [-26, -10, 10] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3474.3 volume_max: 5211.4 description: 'As leftDuctMid45; station: the round rear outlet of the fork at z=10 (section z=10, hole centre ~(-25.5, -9.5)). The flatter front outlet is under 6 mm tall and is closed by the seal, so it is pinned by the leftDuctAir probes instead.' - name: rightDuctMid45 point_a: [20, -18, 55] point_b: [22, -16, 45] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3440.4 volume_max: 5160.7 description: 'Mirror of leftDuctMid45.' - name: rightDuctTrunk30 point_a: [20, -18, 55] point_b: [24, -14, 30] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3440.4 volume_max: 5160.7 description: 'Mirror of leftDuctTrunk30.' - name: rightDuctLower20 point_a: [20, -18, 55] point_b: [27, -12, 20] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3440.4 volume_max: 5160.7 description: 'Mirror of leftDuctLower20.' - name: rightDuctRearOutlet point_a: [20, -18, 55] point_b: [26, -10, 10] pitch: 0.4 seal_radius: 3.2 expect_connected: true volume_min: 3440.4 volume_max: 5160.7 description: 'Mirror of leftDuctRearOutlet.' - name: leftRightDuctIsolation point_a: [-22, -16, 45] point_b: [22, -16, 45] pitch: 0.4 seal_radius: 3.2 expect_connected: false description: 'With the same caps and closing radius, both duct centres at z=45 must be interior air in different components; a common cavity or an outside detour must fail.' thickness: - name: minimumHousingWall min: 0.75 stat: p05 samples: 12000 max_thickness: 8.0 description: 'sources/voron-duct-description.md: fifth percentile of inward ray-cast wall thickness >=0.75 mm. Whole housing, with the same nominal 1 mm walls on both ducts. Rays longer than 8 mm cross an open interior (cavity, duct, hotend pocket) rather than a wall and are dropped, so the statistic reads the walls.' probes: - name: leftDuctAir state: void points: - - -20 - -18 - 55 - - -22 - -16 - 45 - - -24 - -14 - 30 - - -27 - -12 - 20 - - -22 - -8 - 7.5 - - -22 - -22 - 8 description: Measured safe interior centers at inlet, two middle stations, lower trunk, and both outlet branches. Sources section-z55/z45/z30/z20 and section-x-22; contour reading uncertainty <=0.75 mm. - name: rightDuctAir state: void points: - - 20 - -18 - 55 - - 22 - -16 - 45 - - 24 - -14 - 30 - - 27 - -12 - 20 - - 22 - -8 - 7.5 - - 22 - -22 - 8 description: Mirrored core probes, checked against section-z55/z45/z30/z20 and section-x22. These are air; never material/support ribs. - name: fanHubSolid state: solid points: - [0, -23, 41] - [0, -23, 45] - [0, -21, 43] - [0, -25, 43] - [4, -23, 43] - [-4, -23, 43] description: 'The central hub of the fan opening (feature cosmeticFanGrille): a solid boss about 16 mm wide (x -8..8) and 15 mm tall (z ~36..51) spanning the opening depth from the front face to the bore floor; these points sit at least 1.5 mm inside it. Required because sections z=45 and y=-20 are banded with it; the vanes joining it to the rim are optional.' - name: hotendFanFloorSolid state: solid points: - [0, -17, 26] - [0, -16, 28] - [10, -18, 30] - [-13.6, -18.8, 26.4] - [13, -10, 28] - [-13, -8, 32] description: 'Solid body behind the fan bore floor (y = -19.2): the chin under the bore at x=0 (the section x=0 closed outline z 20..29.5 is material, sloping back from y~-22 at z=20 to y~-12 at z=28) and the shoulders beside the hotend pocket (|x| 10..14, z 24..34, y -27..-4). There is no sealed air chamber here; the only interior air near the fan is the bore itself (frontFanAir), the pocket (hotendPocketAir) and the ducts. Do not carve chambers, bays, slots or access slabs in this region; the closing-radius passages measure the ducts only.' - name: hotendPocketAir state: void points: - - 0 - -5 - 36 - - 0 - -5 - 20 - - 0 - -12 - 10 - - 0 - -20 - 10 description: Conservative cavity/access centers from y=-12/-20 and x=0 sections. The approximate 26 x 35 pocket is not promoted to an unsupported rectangular keep-out. - name: backAccessAir state: void points: - - 0 - -5 - 36 - - 0 - -2 - 36 - - 0 - -0.5 - 36 - - 0 - 0.5 - 36 description: Sampled clear path through the open back at y=0; final point intentionally outside the envelope. No cap may close the cavity back. - name: nozzleAccessAir state: void points: - - 0 - -10 - 12 - - 0 - -10 - 8 - - 0 - -10 - 4 - - 0 - -10 - 1 description: Sampled clear downward access through the open nozzle end; final point lies below the part. - name: frontFanAir state: void points: - - 12 - -27 - 45 - - 12 - -24 - 45 - - -12 - -27 - 42 - - -12 - -24 - 42 description: Points inside the round front aperture, away from the visible hub and four optional vane locations; front.png and section-y-20.png. - name: mainMaterialAnchor state: solid points: - - 0 - -10 - 58.8 description: Roof bridge beneath cosmetic engraving, well away from the notch and vertical bores; x=0 section. - name: screwBoreAir state: void points: - - -6.963 - -3.939 - 56 - - 3.939 - -6.963 - 56 - - -6.963 - -3.939 - 59.4 - - 3.939 - -6.963 - 59.4 - - -28 - -2.3 - 19 - - -25 - -2.329 - 35 - - -12.7 - -3.2 - 55.424 - - 12.7 - -3.131 - 55.424 - - -16.25 - -3.75 - 19.301 - - 16.25 - -3.75 - 19.301 description: Ten stated full-360 bore segments from the cylindrical table, including the two stacked segments at each top screw. The smallest radius is 1.35 mm, larger than axis/radius digital uncertainty. - name: topInletAccessAir state: void points: - - -15 - -19 - 60 - - -15 - -19 - 61 - - -15 - -19 - 62 - - 10 - -19 - 60 - - 10 - -19 - 61 - - 10 - -19 - 62 description: Visible mouth interiors from top.png and section-y-20.png, deliberately offset from the thin optional inlet vane traces. Samples straddle z=61.5; the z=62 samples are outside-envelope access endpoints. The z=60 samples are the positive passage endpoints, 1 mm below the test plugs. - name: lowerMountAccessAir state: void points: - - -16.25 - -26 - 19.301 - - 16.25 - -26 - 19.301 - - -16.25 - -20 - 19.301 - - 16.25 - -20 - 19.301 - - -16.25 - -12 - 19.301 - - 16.25 - -12 - 19.301 description: Located void centers of the two front-visible lower screw access paths, corroborated by front.png and sections y=-20 and y=-12. No additional bore diameter or chamfer depth is inferred for this continuation. cylinder_counts: - name: topPilotPair diameter: 2.7 radius_tolerance: 0.15 kind: hole direction: - 0 - 0 - 1 region: - - -9 - -9 - 54 - - 6 - -2 - 58 expected: 2 description: Stated full bores; axis-center region distinguishes similar diameters and coaxial steps. Repeated partial shell fillets are enumerated individually, not treated as fasteners. - name: topCounterborePair diameter: 5 radius_tolerance: 0.15 kind: hole direction: - 0 - 0 - 1 region: - - -9 - -9 - 57.5 - - 6 - -2 - 61.5 expected: 2 description: Stated full bores; axis-center region distinguishes similar diameters and coaxial steps. Repeated partial shell fillets are enumerated individually, not treated as fasteners. - name: lowerMountPair diameter: 3.4 radius_tolerance: 0.15 kind: hole direction: - 0 - 1 - 0 region: - - -18 - -8 - 18 - - 18 - 1 - 21 expected: 2 description: Stated full bores; axis-center region distinguishes similar diameters and coaxial steps. Repeated partial shell fillets are enumerated individually, not treated as fasteners. - name: upperMountPair diameter: 4.6 radius_tolerance: 0.15 kind: hole direction: - 0 - 1 - 0 region: - - -15 - -7 - 53 - - 15 - 1 - 57 expected: 2 description: Stated full bores; axis-center region distinguishes similar diameters and coaxial steps. Repeated partial shell fillets are enumerated individually, not treated as fasteners. - name: rearAuxPair diameter: 4.7 radius_tolerance: 0.15 kind: hole direction: - 0 - 1 - 0 region: - - -31 - -5 - 17 - - -22 - 1 - 37 expected: 2 description: Stated full bores; axis-center region distinguishes similar diameters and coaxial steps. Repeated partial shell fillets are enumerated individually, not treated as fasteners. gears: [] meshes: [] deviation: null blockout: volume_min: 109390.139 volume_max: 120904.891 export_volume_tolerance_rel: 0.002 references: - path: sources/back.png kind: image role: authoritative sha256: d9993a7951305125b17849520dc3e4c593395cd32e33913a96e816f8ad86d78b units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic mm-grid evidence for frame, silhouette, port locations and visible feature counts. - path: sources/bottom.png kind: image role: authoritative sha256: 99a231fa19ee41312e13e5235b253b6171240a53631fbf94471c4e645c9f3465 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic mm-grid evidence for frame, silhouette, port locations and visible feature counts. - path: sources/dimension-sheet.md kind: table role: authoritative sha256: 3d150ee78d7c71e164535fe895088ffa4d6d75114b58edd6328fff4c47c695bf units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Quoted dimension/axis/section tables. Provenance of quoted values is stated; no reference ingest files or reference CAD were read. - path: sources/front.png kind: image role: authoritative sha256: 545e3b87263e28c5d3ec34276955fb4796248332983d2cb49684c082202dbfb3 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic mm-grid evidence for frame, silhouette, port locations and visible feature counts. - path: sources/iso-below.png kind: image role: illustrative sha256: 5414dfaf4b3c5fb32a2a42897ff413d0507e7cb5ee2320238c5b55c837b3bd92 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Overall spatial relationships and optional styling; do not take dimensions from isometric projected lengths. - path: sources/iso.png kind: image role: illustrative sha256: a53d5ef420cd2e45ef1942b8cfd74e9eaeed82b33961f3292e4cd0e1f0478436 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Overall spatial relationships and optional styling; do not take dimensions from isometric projected lengths. - path: sources/iso2.png kind: image role: illustrative sha256: cfb622b1cf2de0621babf230fe4f377a990ef9946d58e5d955b758c9f5ebf12e units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Overall spatial relationships and optional styling; do not take dimensions from isometric projected lengths. - path: sources/left.png kind: image role: authoritative sha256: a83a406028cfd1bc310776c2f0dbc4673dbb2ba88ebff0e472b53ad421a0640d units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic mm-grid evidence for frame, silhouette, port locations and visible feature counts. - path: sources/render-notes.md kind: text role: authoritative sha256: 8e01aeb577033da71d8a610d78928238f48355dce9e0971edbc621f990ca0b6b units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic frame, extents and supplied rendering metadata; reference triangle count is diagnostic. - path: sources/right.png kind: image role: authoritative sha256: 1f14cfe9a9de8a8327a3bc12b991464d85c6adef10c453a56161a6b650cf8b8d units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic mm-grid evidence for frame, silhouette, port locations and visible feature counts. - path: sources/section-x-22.png kind: drawing role: authoritative sha256: 906479b97107a387f93734009e482a1acc4d75a5cb6248f771ca3f3c21a88b61 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-x0.png kind: drawing role: authoritative sha256: 30db4695d01c4e2003cbb782debc4a2b3d23ef76c3c16dd9e909edcc7d102059 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-x22.png kind: drawing role: authoritative sha256: 79b4f1c7e3912577c067c94093f09d39c34c00614892ee0feeb0a53d7e7ae26c units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-y-12.png kind: drawing role: authoritative sha256: 74706b6b2d6db03fda484965c3f4d48bb5b989228adb13b016f3c05e12c11b72 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-y-20.png kind: drawing role: authoritative sha256: e781d9072805478672deecc52820cbd86e53bd009b9fbd069821bc956731ef7e units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-y-5.png kind: drawing role: authoritative sha256: 7bea7ed7c698ff28593792036b35fbc018c616541aab1781bf97c073385a3869 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-z10.png kind: drawing role: authoritative sha256: 8db2da999a0d047e26f34a264313a178cc6239c3dff22ee2cc55c055fa433c96 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-z20.png kind: drawing role: authoritative sha256: 7b13af9a25b7bc409aaae9b72f126ee1fe5588f789c46445f3b6cdfdc88962c9 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-z30.png kind: drawing role: authoritative sha256: 9553a783bcec14250054a90b8a863b43302fb9944fc146c2cbc73f185aabf918 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-z45.png kind: drawing role: authoritative sha256: b72331aead4d9c114de497d1bd77f6ad435396d064b488b73603c04d3c7ca4c8 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/section-z55.png kind: drawing role: authoritative sha256: 8176c82680b60fd3ad92c5b3478a21a6268b169ad22d2f45f0461cf20f413e6b units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Material outline and mm axes; compare label with dimension sheet. Conflicts and optional-region counts are disclosed in the brief. - path: sources/top.png kind: image role: authoritative sha256: c035e03a2df785aafcdb61474a38934d50799a6c09d2ce653e8936d1dadd20cc units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Orthographic mm-grid evidence for frame, silhouette, port locations and visible feature counts. - path: sources/voron-duct-description.md kind: text role: authoritative sha256: 6393278735f162422209a12eb2ac58b40a8446fd7ebd46f9d419992a8b322623 units: mm revision: Supplied reconstruction bundle; upstream commit/revision not stated; content pinned by sha256. note: Functional routing, cavity, closed/separate ducts, thickness statistic, cosmetic priority and GPL-3.0 source attribution. open_questions: - Q1. Which section source is correct at y=-5 (table 1726.99 mm2, 3 loops/6 holes; image 55.37 mm2, 5 regions) and z=20 (table 765.96 mm2; image 618.29 mm2)? The draft uses table areas, a disclosed 25% z=20 band, and leaves exact y=-5 loop/hole counts unpinned pending resolution. - Q2. Does mirrored ducts mean exact mirrored top mouths as well as the principal routes and forks? The description suggests mirrored inlets, but top.png shows left x~-25..-10 and right x~5..18. The draft mirrors the core routes and probe stations while recording the visible asymmetric mouth transitions. - Q3. What are the exact loft centerlines, section profiles, bend radii, fork-divider shape and port boundaries between the supplied stations? Interpolate the shown routes with the stated nominal walls; do not invent unseen hardware geometry. - Q4. What are acceptable sealed air-volume ranges for each duct, and do the six proposed drawing-based plug boxes seal only the actual ports? No source gives per-duct volume limits; the passage checks report volume without a numeric band, and plug behavior needs validation against the eventual model. - Q5. How should the approximate 26 x 35 mm hotend pocket at z~9..44 be reconciled with the larger fan transition and z=54 rear roof? No hotend hardware envelope, exact cavity depth or fit clearance is supplied; no rectangular hardware keep-out is assumed. - Q6. What are the angular trim limits of the 20 partial cylindrical patches, the screw entry/chamfer profiles, and the lower mounting bores beyond the documented y=-7.5..0 segment? The axis/radius/length table is pinned, but full bores or full pins must not replace partial surfaces. - Q7. Which material, density, printing process details, shrink allowance and fit tolerances are intended? Material and density remain unknown; all tolerances here are digital reconstruction comparisons, not manufacturing qualification. - Q8. What upstream revision and cosmetic detail level should be retained? Source hashes pin this bundle, but no upstream commit, font, engraving depth, grille thickness or complete optional facet radii are provided; exterior mass properties remain diagnostic and hidden geometry is not scored.